Rate Us:
★ ★ ★ ★ ★

When an Office Network Needs New Cabling, Not Just New Equipment

Office Network Cabling

A slow or unreliable office network doesn’t always mean the building needs new Ethernet cabling. The problem could be an aging switch, poor Wi-Fi coverage, a damaged connection, or an internet service that no longer meets the business’s needs.

Before replacing network cables, it helps to identify where performance is failing and whether the existing wiring can support your next equipment upgrade. In many offices, targeted repairs or equipment changes can solve the problem without the cost and disruption of recabling the entire building.

How to Tell Whether Cabling Is Causing Network Problems

Network performance problems can look similar even when they have different causes. A computer that frequently disconnects may have a damaged cable, while slow connections throughout the office may point to the internet service or network equipment.

Start by looking at which devices are affected and when the problem occurs.

Network problem Possible cause What to check first
One workstation frequently disconnects Patch cord, wall jack, network adapter, or cable run Try another patch cord and a known-working network connection
Several computers slow down at the same time Internet service, network congestion, or shared equipment Compare wired network and internet performance during busy periods
Wired connections work, but Wi-Fi is unreliable Access point placement, wireless interference, or capacity Test coverage and performance in affected work areas
A connection negotiates at 100 Mbps instead of 1 Gbps Port configuration, device capability, damaged cable pairs, or termination problems Check both network ports and test the connection with known-working equipment
Network phones or cameras lose power Insufficient Power over Ethernet capacity, cabling, or device issues Check switch power availability and the affected connections

A connection that improves after replacing a patch cord generally doesn’t justify replacing the cable inside the wall.

If the problem remains associated with the same wall jack after testing with other equipment, the permanent cable and its terminations deserve closer inspection.

When several symptoms occur at once, a broader business IT assessment can help identify whether the problem involves wiring, network equipment, or the internet connection.

Can Your Existing Ethernet Cabling Support Faster Speeds?

Older network cabling is not automatically obsolete. Many offices already have wiring capable of supporting faster connections than their existing switches provide.

The most common Ethernet cable categories in business environments are Cat5e, Cat6, and Cat6A.

Cable category Common supported applications Upgrade consideration
Cat5e 1 Gbps and, on suitable installations, 2.5 Gbps over standard distances May support faster switches without replacement
Cat6 1, 2.5, and 5 Gbps over standard channel distances; some shorter 10 Gbps runs A practical option for many existing and new office connections
Cat6A Up to 10 Gbps over a compliant 100-meter channel Useful for higher-speed networks and long-term infrastructure planning

These capabilities depend on cable condition, installation quality, connected equipment, and applicable standards.

Cable Length and Installation Quality Matter

For standard twisted-pair Ethernet installations, the maximum channel length is generally 100 meters, including patch cords. The permanent cable installed through walls and ceilings is typically limited to 90 meters.

A cable that exceeds those limits may require a different network layout or a closer equipment location rather than simply replacing it with a higher category.

Cat6 can also support 10 Gbps over shorter distances, commonly discussed in the 37- to 55-meter range depending on installation conditions and interference. Cat6A is designed to support 10 Gbps over a compliant 100-meter channel.

However, cable category alone doesn’t guarantee performance. Poor terminations, damaged connectors, excessive bending, or interference can prevent an installation from meeting its expected capability.

Before investing in new wiring, have the existing runs tested against the network speeds your business needs.

When New Network Cabling Is Worth the Investment

Some upgrades can work with existing wiring. Others make recabling a sensible investment, especially when the business plans to keep using the space for years.

Damaged or Failing Cable Runs

Repeated connection problems tied to the same wall jack can indicate a damaged cable or faulty termination.

In some cases, replacing a connector or repairing a termination solves the problem. If the permanent cable fails appropriate testing or has physical damage that cannot be repaired reliably, replacement may be necessary.

One failed cable doesn’t mean the rest of the building needs new wiring.

Upgrading to 10 Gigabit Networking

Businesses transferring large design files, working with local servers, or supporting demanding applications may benefit from faster internal network connections.

Cat6A is worth considering when new installations need reliable 10 Gbps connectivity over longer runs.

Existing Cat6 may still support 10 Gbps at shorter distances if the installed cabling meets the relevant performance requirements.

The decision should account for the network equipment, required speeds, cable lengths, and measured condition of the existing installation.

Installing Wi-Fi 7 Access Points

Newer wireless access points can support faster wired uplinks and may require more electrical power than older models.

Before replacing cables for a Wi-Fi 7 upgrade, verify:

  • The wired connection speeds supported by the access points
  • The capabilities of the existing Ethernet cabling
  • Whether the network switches have suitable multi-gigabit ports
  • Whether the switches can supply the required Power over Ethernet (PoE) power

For example, Cisco’s CW9178I Wi-Fi 7 access point supports faster uplinks when adequate power is available. Certain configurations reduce radio capabilities or wired uplink speeds when supplied with lower-power PoE.

Those limitations depend on the specific model and software configuration.

An access point may therefore benefit from a switch upgrade even when the existing cable is suitable. For new runs serving high-performance access points, Cat6A can provide additional capacity for future network requirements.

Supporting High-Power PoE Devices

Power over Ethernet allows network cables to carry both data and electrical power to devices such as access points, cameras, and IP phones.

Higher-power devices can place additional demands on the cabling installation. Cable resistance, bundle sizes, ambient temperature, and installation methods all affect performance and heat management.

TIA’s TSB-184-A guidance addresses these considerations and recommends Cat6A or higher-performing cabling for new PoE installations, along with appropriate cable-bundling practices.

This doesn’t mean existing Cat5e or Cat6 runs must automatically be replaced when a business adds cameras or phones.

The network design should account for the actual devices, power requirements, cable condition, and installation environment.

How to Test Network Cabling Before Replacing It

Testing helps establish whether existing wiring is suitable or if replacement is necessary.

Different testing methods answer different questions.

Testing method What it tells you When it’s useful
Verification Whether conductors are connected correctly and basic wiring faults exist Initial troubleshooting of individual connections
Qualification Whether an installed cable link can support a particular network technology or speed Evaluating existing cabling for an equipment upgrade
Certification Whether the installation meets a specified cabling category or performance standard New installations, warranty requirements, and formal cabling acceptance

A basic wiremap tester can identify connection problems, but it doesn’t measure all the electrical performance characteristics needed to certify cabling.

A certification tester performs additional measurements, including signal loss and crosstalk, and compares the results with the applicable standard.

Fluke Networks explains these differences in its guide to cable verification, qualification, and certification.

What to Request After a New Cabling Installation

For new structured cabling, request certification results for each installed run.

The documentation should include:

  • A PASS or FAIL result against the specified cable category
  • Cable length and wiring configuration
  • Relevant signal-loss and crosstalk measurements
  • Consistent identification of each cable run
  • Labels matching the wall jack, patch panel, and floor plan

These reports provide evidence that the installed cabling meets the agreed standard.

For existing wiring, the appropriate test depends on the problem. Qualification testing may be sufficient when determining whether a connection can support a planned network speed, while certification is appropriate when formal standards compliance must be established.

Testing before replacement helps avoid unnecessary work and gives the business a clearer basis for comparing cabling quotes.

When You Can Keep Your Existing Network Cabling

A full recabling project may not be necessary if the wiring remains in good condition and supports the network’s current and planned requirements.

Existing cabling is worth keeping when:

  • Cat5e or Cat6 connections pass appropriate testing for the speeds required
  • Network issues can be traced to switches, wireless equipment, or internet service
  • Only a limited number of cable runs are damaged or unreliable
  • New access points can operate effectively using existing suitable connections
  • The business plans to relocate soon and can address future cabling needs at the new site

In these cases, replacing selected components or repairing individual cable runs can be more cost-effective than rewiring the entire office.

A network assessment can identify which improvements are necessary now and which can be planned for a later infrastructure upgrade.

Plan Cabling Upgrades Around an Office Move or Remodel

An office move, renovation, or expansion is often a practical time to improve structured cabling.

With ceilings and walls accessible, installation work may be easier to coordinate and less disruptive than replacing cables after the space is occupied.

Planning should account for current equipment and future growth.

A cabling specification may include:

  • Cat6 or Cat6A based on connection speeds and expected equipment needs
  • Appropriate cabling for wireless access points and powered devices
  • Additional connections in meeting rooms and areas likely to change
  • Cable lengths within applicable installation limits
  • Suitable routes and bundle arrangements for PoE
  • Clear labeling at both ends of every cable
  • Certification results and updated network documentation

Also consider where switches, network closets, and future workstations will be located.

A well-planned installation gives the business room to upgrade network equipment without repeatedly reopening walls or ceilings.

Plan Your Office Network Cabling Upgrade With Covergent

Before investing in new network cabling, it’s worth confirming whether your existing wiring is causing performance problems or limiting the equipment you plan to install.

Covergent’s network and infrastructure services help businesses assess their network infrastructure, identify cabling needs, and plan upgrades that support reliable connectivity.

Whether you’re troubleshooting unreliable connections, installing new network equipment, or preparing for an office renovation, Covergent can help determine which cables need attention and where existing infrastructure can continue to serve your business.

Contact Covergent to discuss your network cabling requirements and plan the right improvements for your office.

Call us or send a message today.

We’re ready when you are. 

Partner With the Right People

Connect with Covergent Technologies today and get the support your business deserves.

What can we do better?

We love to hear from our clients, please let us know if there are any areas that you think we could improve upon.